Euromix™ Extreme High Build
Euromix™ Extreme Highbuild render is an innovative, lightweight, high-build polymer modified levelling compound engineered using 100% recycled eco-aggregates. It is one third the weight per square metre of traditional base coat renders. It is designed for use as a base coat with superior coverage and can be built up to 50mm in a single coat. Euromix™ Extreme Highbuild can be applied over substrates, like autoclaved aerated concrete blocks / panels (AAC), fibre cement sheeting (FC), off-form concrete and expanded polystyrene sheet (EPS) / NRG green board surfaces.
Euromix™ Extreme Highbuild is a premium pre-blended render that requires the addition of water only. Manufactured with 100% recycled aggregate, it provides an environmentally responsible solution without compromising quality. Its lightweight formulation offers excellent workability.
General Direction For Use
Ensure that all elements to be rendered have been constructed and fixed in accordance with the project plans / specifications and the substrate manufacturer’s recommendations. The substrate should be dry and free of any material that may affect the ability of the Euromix™ Extreme Highbuild to adhere to the surface (dirt, dust, mould oils, loose friable material, etc.).
Mask windows and architectural trim elements before applying render. Floor and adjacent walling materials should be protected against spills and splashes by plastic film or similar.
Mixing the Render
One bag of Euromix™ Extreme Highbuild will yield approximately three
15-litre pails of mixed material. Euromix™ Extreme Highbuild render's content is designed to enable the render to be mixed using water only. For smaller batches, add approximately 4 litres of clean, potable water to a 15-litre pail, then gradually add one-third of the Euromix™ Extreme Highbuild bag while mixing with a suitable power mixing drill until a smooth, lump-free consitency is achieved. To mix a full bag of Euromix™ Extreme Highbuild, place approximately 10-12 litres of clean water into a 40-litre mixing container, then slowly add the entire contents of the bag while continuously mixing. Allow the mix to stand for 2-3 minutes before application, then remix briefly if require prior to use.
Allow the wet render to ‘stand’ for 3 minutes after first mixing, then remix to achieve consistent slurry. The render is now ready for application. One 15 Kg bag of Euromix™ LWHB Render requires @ 5 litres of water in mixing.
Typical Application Method
Apply Euromix™ Extreme Highbuild using a clean hawk and trowel or suitable mechanical spray pumping equipment. Place the material at a thickness to fill irregularities and achieve the required wall alignment. Apply Euromix™ Extreme Highbuild in layers of 6mm-50mm thicknesses. It can be levelled using an aluminium straight edge to achieve a flat and even finish. Allow the render to dry before carrying out any subsequent finishing coats.
Set time will depend on substrate, moisture, applied thicknesses and weather conditions. Allow at least 24-72 hours between coats.
Curing
Rapid drying of the surface can cause cracking and result in a low strength / friable render. Do not apply Euromix™ Renders when conditions will be above 35ºC, especially if windy. Do not attempt to apply when the temperature is below 10ºC or where the chill factor is high. Ensure that the curing render is protected from rain, extreme frosts and other sources of excess moisture. The drying and curing times are given as a guide only (for normal weather conditions, at 25ºC and 50% RH.
Surface dry
Twelve (12) hours (depending on applied thickness).
Recoat with render
Three (3) days (depending on applied thickness).
Texture & Paint
Three (3) days for acrylic texture & paints. Twenty-one (21) days for oil / alkyd-based paints.
Warranty
The product use information on this bag is provided in good faith and the product is sold on the basis that it is used for its intended purpose and is applied in a proper workmanlike manner in accordance with the instructions of the relevant Euromix™ recommendations in suitable and safe working conditions. Under no circumstances will Euromix™ be liable for loss, consequential or otherwise, arising from the misuse of the product.
Euromix™ will replace any material that is found to be of faulty manufacture or unsuitable for use as detailed in Euromix™ literature. This Warranty is provided in lieu of all other warranties, whether expressed or implied, and all other obligations on the part of Euromix™, apart from any warranties or conditions which arise by operation of law and which may not be negated or modified.
Related Products
Euromix™ Renders are premium acrylic modified cement-based renders, designed to provide weather resistant, decorative, render finishes, suitable for application over most building material substrates in interior and exterior wall and ceiling applications. Euromix™ Cream, Skim and Render are AS1530.1 Non-Combustible Certified Renders.
Euromix Render
Euromix™ Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 4mm to 8mm at a time.
Euromix Full Polymer
Euromix FP Render is a dry mix, full polymer, cement based render formulated for application over sheet and panel substrates, like, autoclaved aerated concrete (AAC),expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix FP Render is mixed with water only (no added Bond).When used as a base coat, Euromix FP Render can be applied up to 3-4 mm thick in one coat (over masonry and similar solid substrates).
Euromix Cream
Euromix™ Cream Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 4mm to 8mm at a time.
Euromix NPS Keycoat
Euromix™ NPS Base Render is a dry mix, full polymer, cement based render formulated for application over non porous sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix™ NPS Base Render is mixed with water only (no added Bond).
Euromix LWHB High Build
Euromix™ LWHB Render is a lightweight dry mix, full polymer, cement based render formulated for use where a high build finish is required. Euromix™ LWHB can be applied over most masonry and sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS) and fibre cement (FC). Euromix™ LWHB Render is mixed with water only (no added Bond required).
