Euromix FP Render


Euromix™ FP Render is a ready-to-use dry mix, full polymer, cement based render formulated for application over sheet and panel substrates, like, autoclaved aerated concrete (AAC),expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix™ FP Render is mixed with water only (no added Bond).When used as a base coat, Euromix™ FP Render can be applied up to 3-4 mm thick in one coat (over masonry and similar solid substrates).

Euromix™ FP Render is specifically designed to meet BCA (Building Code of Australia) standards for non-combustible building materials, and is fully compliant with AS1530.1.

Download Product Data Sheet

Download Material Safety Data Sheet

General Direction For Use


Ensure that all elements to be rendered have been constructed and fixed in accordance with the project plans / specifications and the substrate manufacturer’s recommendations. The substrate should be dry and free of any material that may affect the ability of the Euromix™ FP Render to adhere to the surface (dirt, dust, mould oils, loose friable material, etc.).

Mask or otherwise protect adjacent building elements and areas (windows, doors, roof coverings, paving, etc.) against inadvertent coating with render. Polymer modified renders are very difficult to remove once cured and can cause staining of certain materials.

Mixing The Render


Euromix™ FP Render‘s polymer content is designed to enable the render to be mixed using water only. The required volume of clean, potable water should be poured into a mixing bucket. Then, steadily add the Euromix™ FP Render powder to the water while mixing it using a suitable drill (or traditional concrete mixer), until it is smooth and lump free - this normally takes 3 to 4 minutes.

Allow the wet render to ‘stand’ for 3 minutes after first mixing, then remix to achieve consistent slurry. The render is now ready for application. One 20 Kg bag of Euromix™ FP Render requires @ 4 litres of water in mixing.

Typical Application Method


Apply a first coat of Euromix™ FP Render to the desired thickness with hawk & trowel. Maximum coat thickness is 4mm. Use a straight edge to achieve a true and level finish.

Once the first coat of render has dried (at least 24 hours in normal conditions) prepare a topping coat of Euromix Skim Coat Render or Finishing Render with a solution of 1 part Bond to 19 parts water, then apply this to a nominal thickness of 2mm, using a trowel and straight edge to achieve a true and level finish.

For a flat smooth finish (ready for painting or the application of an acrylic texture coating) use a polystyrene, wood or plastic float. For a textured render (ready for painting) use a suitable sponge float to bring the sand grains to the surface.

Curing


Rapid drying of the surface can cause cracking and result in a low strength / friable render. Do not apply Euromix® Renders when conditions will be above 35ºC, especially if windy, nor where the temperature is below 5ºC or where the chill factor is high. Ensure that the curing render is protected from rain, extreme frosts and other sources of excess moisture (e.g.; overflowing gutters and down pipes). The drying times quoted below are for normal weather conditions, at 25ºC and 50% RH.

Surface dry

Four (4) hours.

Recoat with render

One (1) day.

Applying Texture Coating

Three (3) days.

Applying Paint

Three (3) days for acrylic paints. Twenty-one (21) days for oil / alkyd based paints.

Warranty


The product use information on this bag is provided in good faith and the product is sold on the basis that it is used for its intended purpose and is applied in a proper workmanlike manner in accordance with the instructions of the relevant Euromix recommendations in suitable and safe working conditions. Under no circumstances will Euromix be liable for loss, consequential or otherwise, arising from the misuse of the product.

Euromix replace any material that is found to be of faulty manufacture or unsuitable for use as detailed in Euromix literature. This Warranty is provided in lieu of all other warranties, whether expressed or implied, and all other obligations on the part of Euromix, apart from any warranties or conditions which arise by operation of law and which may not be negated or modified.

Download Product Data Sheet

Download Material Safety Data Sheet

WHERE TO BUY

Related Products


Euromix™ Renders are premium acrylic modified cement based renders designed to provide weather resistant, decorative, render finishes, suitable for application over most building material substrates in interior and exterior wall and ceiling applications. Euromix™ Cream, Skim and Render are AS1530.1 Non-Combustible Certified Renders.

'}}
Euromix Render

Euromix Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 2mm to 6mm at a time.

'}}
Euromix Skim Coat Render

Euromix™ Skim Coat is designed to be used as a finishing coat over base render or other finished surfaces. Euromix™ Skim can be applied in thicknesses from 1 to 4mm and be floated to a smooth flat finish or sponged to give an even textured finish.

'}}
Euromix FP Render

Euromix FP Render is a dry mix, full polymer, cement based render formulated for application over sheet and panel substrates, like, autoclaved aerated concrete (AAC),expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix FP Render is mixed with water only (no added Bond).When used as a base coat, Euromix FP Render can be applied up to 3-4 mm thick in one coat (over masonry and similar solid substrates).

'}}
Euromix Cream Render

Euromix Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 2mm to 6mm at a time.

'}}
Euromix NPS Keycoat Render

Euromix™ NPS Base Render is a dry mix, full polymer, cement based render formulated for application over non porous sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix™ NPS Base Render is mixed with water only (no added Bond).

'}}
Euromix LWHB High Build Render

Euromix™ LWHB Render is a lightweight dry mix, full polymer, cement based render formulated for use where a high build finish is required. Euromix™ LWHB can be applied over most masonry and sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS) and fibre cement (FC). Euromix™ LWHB Render is mixed with water only (no added Bond required).

'}}
Euromix Fine coat Texture

Euromix™ Finecoat is a pre mixed, polymer based texture coating, designed for decorative finishing over Euromix™ Renders and other substrates.

'}}
Euromix Patch Coarse

Euromix™ Patch Coarse is a pre mixed polymer render that is suitable for use as a low build render coat and patching material in both external and internal applications over masonry and sheet substrates like fibre cement.

'}}
Euromix Patch Fine

Euromix™ Patch Fine is an acrylic polymer, fine grain, topping and patching compound, suitable for use with most building substrates, in both internal and external applications.

'}}
Euromix AAC Adhesive

Euromix™ AAC Adhesive is specially formulated for bonding aerated autoclaved concrete (AAC) lightweight panels and blocks.