Euromix™ Euroflex
Euromix™ Euroflex is a high solid, acrylic based waterproofing and decorative paint coating that provides excellent flexibility, elasticity and durablility on surfaces subjected to high winds, salt spray and severe weather conditions.
Product Summary
Euromix™ Euroflex is most often used as the final coloured topcoat over render and texture coated surfaces. It provides an effective waterproofing barrier that also breathes - allowing vapor to escape from the substrate. Euroflex is suitable for coating most prepared building substrates including; off-form concrete, cement render, fibre cement sheeting and brick and block work.
Product Name
Euromix™ Euroflex
Packaging
15 litre plastic buckets.
Appearance
In the bucket the material appears as a wet, off-white, thick liquid.
Application
It is recommended that the Euromix™ Euroflex be thoroughly stirred in a bucket using a power stirrer, prior to application.
It can be applied by brush, roller or spray in a minimum of two coats (if applying by roller, it is recommended that a 6-8mm nap roller sleeve be used) at the rate of 1.5 SQM / litre per coat.
Allow a minimum of six (6) hours drying between coats.
Do not apply Euromix™ paints and Textures in windy conditions or when temperatures are outside the range 10°C to 30°C. Keep newly coated areas protected from rain and moisture for at least twelve (12) hours, longer in the lower temperature range. Direct exposure to rain is not the only issue - run-off or wind driven moisture can also cause coating failure.
Drying and Curing
Drying and curing of the product is affected by type, dryness and porosity of the surface, temperature, humidity, ventilation, climate conditions and application technique and therefore drying and curing can only be given as a guide (at 25°C & 50% RH):
Touch Dry
Two (2) to four (4) hours.
Recoat
Six (6) hours.
Related Products
Euromix™ Primers and Paints not only provide the colour for your wall or ceiling finish, they also improve the functionality of the finish system.
Euromix Render
Euromix™ Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 4mm to 8mm at a time.
Euromix Full Polymer
Euromix FP Render is a dry mix, full polymer, cement based render formulated for application over sheet and panel substrates, like, autoclaved aerated concrete (AAC),expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix FP Render is mixed with water only (no added Bond).When used as a base coat, Euromix FP Render can be applied up to 3-4 mm thick in one coat (over masonry and similar solid substrates).
Euromix Cream
Euromix™ Cream Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 4mm to 8mm at a time.
Euromix NPS Keycoat
Euromix™ NPS Base Render is a dry mix, full polymer, cement based render formulated for application over non porous sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix™ NPS Base Render is mixed with water only (no added Bond).
Euromix LWHB High Build
Euromix™ LWHB Render is a lightweight dry mix, full polymer, cement based render formulated for use where a high build finish is required. Euromix™ LWHB can be applied over most masonry and sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS) and fibre cement (FC). Euromix™ LWHB Render is mixed with water only (no added Bond required).
