Euromix™ Render

Euromix™ Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 2mm to 6mm at a time.

Euromix™ Render is specifically designed to meet BCA (Building Code of Australia) standards for non-combustible building materials, and is fully compliant with AS1530.1

Download Product Data Sheet

Download Material Safety Data Sheet

Product Description

Euromix™ Render, when used in conjunction with Euromix™ Bond, is an acrylic modified cement based render suitable for application over most substrates including clay and cement bricks/blocks, pre cast or site poured concrete, calcil bricks, aerated concrete blocks/panels, expanded polystyrene and styrofoam surfaces (approved alkali resistant fibre glass mesh must be used when applied to polystyrene and styrofoam surfaces). Euromix™ Render is designed for use as a base coat render, applied in layers ranging from 2mm to 6mm at a time (higher thickneses can be achieved with multiple coats).

The applicator must ensure the surface to be rendered is stable and free of adhesion inhibiting materials such as dust, grease, dirt, fungus mould releasing agents, excessive water etc .Euromix™ Render provides a weather resistant, stable protective surface for subsequent coatings of paint, trowelled on coatings etc.

Mixing Instructions

Euromix™ Render can be mixed (with the correct ratio of Euromix™ Bond/water) by mechanical mixer or with a traditional concrete mixer. Add the required volume of Bond/water to the mixing bucket or concrete mixer the steadily add the Euromix™ Render until the mixture will hold a soft peak on a hawk.

Too soft a mixture will run off the hawk and requires extra time before the surface can be finished up; too hard a mixture becomes difficult to apply and finish.

Application

Ensure the surface is clean, then; apply the render to the substrate using a steel trowel, taking care to coat evenly. The surface can then be ruled off with a straight edge to level the surface. When the material has firmed sufficiently it can be floated with a large polystyrene, wooden or plastic float. On completion of this process and after application of a finishing coat of Euromix™ Skim Render, the area can again be floated finish with a polystyrene, wooden or plastic float

to further flatten the surface for the application of texture coating finish or with a suitable sponge float, to bring the sand to the surface and finish to a sponge finish, ready for painting.

Coverage

When mixed and applied correctly, 20kgs of Euromix™ Render should cover from 2 to 4 square meters, depending on the thickness of the layer and on how straight and true the substrate is.

Download Product Data Sheet

Download Material Safety Data Sheet

WHERE TO BUY

Related Products

Euromix™ Renders are premium acrylic modified cement based renders designed to provide weather resistant, decorative, render finishes, suitable for application over most building material substrates in interior and exterior wall and ceiling applications. Euromix™ Cream, Skim and Render are AS1530.1 Non-Combustible Certified Renders.

Euromix Render

Euromix Render is a multipurpose render, suitable for use both as a base coat where finishing renders, texture coats, etc. or architectural finishes (like tiles) are to be applied and as a finish coat, where a high quality sponge finish is required. It can be applied by hand or by machine, in layers ranging from 2mm to 6mm at a time.

Euromix Skim Coat Render

Euromix™ Skim Coat is designed to be used as a finishing coat over base render or other finished surfaces. Euromix™ Skim can be applied in thicknesses from 1 to 4mm and be floated to a smooth flat finish or sponged to give an even textured finish.

Euromix FP Render

Euromix FP Render is a dry mix, full polymer, cement based render formulated for application over sheet and panel substrates, like, autoclaved aerated concrete (AAC),expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix FP Render is mixed with water only (no added Bond).When used as a base coat, Euromix FP Render can be applied up to 3-4 mm thick in one coat (over masonry and similar solid substrates).

Euromix Cream Render

Euromix NPS Keycoat Render

Euromix™ NPS Base Render is a dry mix, full polymer, cement based render formulated for application over non porous sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS), fibre cement (FC) and plaster based materials. Euromix™ NPS Base Render is mixed with water only (no added Bond).

Euromix LWHB High Build Render

Euromix™ LWHB Render is a lightweight dry mix, full polymer, cement based render formulated for use where a high build finish is required. Euromix™ LWHB can be applied over most masonry and sheet and panel substrates, like, autoclaved aerated concrete (AAC), expanded polystyrene (EPS) and fibre cement (FC). Euromix™ LWHB Render is mixed with water only (no added Bond required).

Euromix Fine coat Texture

Euromix™ Finecoat is a pre mixed, polymer based texture coating, designed for decorative finishing over Euromix™ Renders and other substrates.

Euromix Patch Coarse

Euromix™ Patch Coarse is a pre mixed polymer render that is suitable for use as a low build render coat and patching material in both external and internal applications over masonry and sheet substrates like fibre cement.

Euromix Patch Fine

Euromix™ Patch Fine is an acrylic polymer, fine grain, topping and patching compound, suitable for use with most building substrates, in both internal and external applications.